Skip to main content

A guide to disassembling the Ricoh GR for sensor cleaning by Jamie Collinson

The Ricoh GR is an excellent camera. A camera which has managed to displace all my former dalliances due to it’s small size, near-perfect ergonomics and incredible performance. But it does have a design flaw. Dust gets sucked into the lens assembly far too easily.
On a recent trip I found lots of annoying dust spots. This is easy to fix, but tedious when you need to go through every. Single. Frame.I’d heard that cleaning the sensor wasn’t too difficult, but the best guide I found online was missing some details. I thought I’d put together a full guide with pictures.

Preparations

  • Remove the memory card and battery
  • Prepare your tools
    • Ricoh GR
    • Crosshead screwdriver
    • Something thin and flat - I used a couple of flathead screwdriver heads
    • [optional] Tweezers to assist in unpinning a data cable
Prepare

Removing the back panel screws

There are 5 screws to remove before you can separate the front and back halves of the camera. Four are externally visible, but one is hidden underneath the handgrip. Start by using a flathead screwdriver to lift the grip.
Lift the grip
Once lifted you’ll see two screws. Remove the lower one - rightmost in the following picture. This is screw #1.
Grip lifted
Replace the grip covering. It should go back into place easily. Now remove the screw above the grip. This is screw #2. I’d recommend keeping the screws somewhere they won’t be easily knocked over. The hotshoe cover works nicely!
Remove screw abovegrip
On the opposite end of the camera, remove the screw below the effect button, on the back of the camera. This is screw #3.
Effects button screw
Make sure the battery hatch is locked, then remove the two rear plate screws on the bottom of the camera. These are screws #4 and #5.
Bottom screws
On my GR at least the 5 screws are the same diameter but different lengths. The under-grip screw and bottom screws are longer than the two from the sides of the camera.
Screw lengths
Due to the different lengths, I stored the screws separately to make putting the camera back together easier.
Screw storage

Removing the hotshoe

Now we’ll remove the hotshoe. Use a flathead screwdriver to lift one of the side springs. This doesn’t take much pressure. Look ahead to see the piece we’re removing, and the following two steps will make more sense!
Lift spring
Then lever the spring away from the front of the hotshoe. Because you’ve already lifted the spring up it will slide back easily once unseated.
Slide hotshoe spring back
Once the spring is removed the four screws holding the hotshoe in place will be revealed.
Remove hotshoe spring
Remove the four screws and lift the hotshoe.
Remove hotshoe
Take a breather. You’ve removed all the necessary case screws and should have all nine safely stowed away.
Screws

Detaching the back panel

Now remove the back of the camera. Start by lifting from the bottom.
Lift bottom of camera
The back of the case is hooked in near the iso adjust lever. By slightly lifting the camera’s top panel - made possible by screw #2 above - it’s easier to pull the back panel away.
Lift top panel
Now you should be able to separate the back panel from the body. Do this gently and be careful not to pull on the cable which connects the body to the front panel. The next step shows the cable.
Back panel detached
Here’s the cable to watch out for.
Cable beware
Lift the back panel from the screen side so that you can get at the cable.
Separate back panel
Use the tweezers to disconnect the white cable. (It may be possible to continue without doing this, but I was concerned about yanking the cable.)
Detach white cable
You now have the back panel detached!
Back panel is now detached

Removing the screen

We now need to get behind the screen. Remove the two screws holding it in place, but don’t lift yet, as the red and black wires which are clipped into the screen surround need unclipping first.
Remove screen screws
Use the tweezers to unclip the red and black wires from the six clips around the screen. In my case I gently bent the clips back first to avoid pinching the wires. According to the thread linked above these wires are for the video mode microphones. I don’t use video at all, but would still prefer my camera to be fully functional!
Unclip wires

Accessing and cleaning the sensor

With the wires unclipped you can lift the screen over. I chose not to remove the brown cable as it seemed simpler to keep it attached and there doesn’t seem much risk of yanking the cable out.
Lift screen
Below the screen is the sensor housing. Remove the three screws holding it down. Each screw has a tension spring, so be careful not to lose it as you remove them. You should now have 14 screws collected.
Screw collection
Lift over the sensor housing. You can now clean the sensor and screen leading to the lens assembly. I used a microfibre cloth and rocket air blower. I also found shining a light on the sensor and viewing from multiple angles helped me see the spots of dust - they’re much smaller than you’d imagine from the resulting image! You can see how poor the fit is on the rubber gasket surrounding the sensor.
Sensor
Follow the above steps in reverse order to reassemble the camera. You can do a partial assembly then take a picture of a white wall at f16 to check if you’ve removed all the spots.

Conclusion

Dust spots seem a fairly common problem mentioned in online threads, so hopefully this guide will help someone. If not it will at least be an aide memoire when I need to repeat the process.
So far I’ve avoided purchasing the Ricoh GR II as the new features (wifi + some new filters) don’t seem worth the upgrade, and from what I hear dust is still a problem. I really hope that the future Ricoh GR III both exists and improves the dust sealing. If Ricoh continues their two year release cycle we’ll find out in 2017.
Soure(https://jamiecollinson.com)

Comments

Popular posts from this blog

RICOH GR MONOCHROME ....

Ricoh has a new patent (2016-201400) field in Japan for a Bayer sensor without a colour filter array (CFA) which should create sharper monochrome images. If dreams could come true a Ricoh GR Monochrome (ala Leica) would be an absolute corker.
We are all holding our breath for the Next incarnation of the Cult Ricoh GR APSC Camera. A 'Ltd Edition Monochrome' camera would be fantastic indeed.  Finger, toes and balls crossed.
Source (http://pentaxrumors.com/)image(https://gr.ricoh-imaging.eu/)

Leica Q vs Ricoh GR

Quick comparison between the Leica Q & Ricoh GR .........Posted with Blogsy

VSCO FILM® 07 & Ricoh GR

Nice indeed, I'm really enjoying this pack. There is enough variety here that makes it worth the purchase, especially with the launch discount and stackable loyalty discount if you've purchased any one of their film packs before. Even still, VSCO packs are never cheap, and if you're wanting to get a good idea of the power of these presets and how easy they are to use, the new VSCO Film 00is aFREEstarter pack from VSCO - It has both Kodak Tri-Xand Kodak Gold 100. Back in the day, thats almost all one would need, so give it a crack - it's got more than just two presets, with all the variants you would expect (Kodak Tri-X 400 ++ anyone? :p )

VSCO Film 07 is available from the VSCO website,